Workshop dust collection

As with any space that is being built from scratch, systems (electrical, HVAC, etc) are always the starting point. The workshop got an extra system: dust collection. It’s a series of PVC pipes that ring the space and connect to a heavy-duty suction machine.


It’s kind of hard to tell what’s what in the photo above, so here are some handy arrows.


Dust collection in a workshop is important in terms of cleanliness and health. This space has zero outside venting so it was critical.

Besides the vacuum itself, the system is mostly built from 6″ PVC DWV pipe and fittings (which are remarkably hard to find.) Aaron started by creating a trunk line with one run for each side of the workshop. He used 45 degree angles for better air flow.


PVC can be glued, but he opted to use the same brand of pipe to ensure things would sit snugly. The screws give a little extra security and can be removed if the system needs to be cleaned out.

002workshop_dust_collection 003workshop_dust_collection

Here’s the trunk line in place.

004workshop_dust_collection 005workshop_dust_collection

Blast gates section off the air flow. They keep the air running in one direction and to one tool to ensure maximum suction.


These parts don’t fit perfectly with the PVC pipe because they’re made for metal piping that costs twice as much as PVC. Obviously, PVC is much more economical for home workshops. The blast gates just need a bit of a hack. Aaron wrapped the fitting of the blast gate with electrical tape to give it a good seal.

007workshop_dust_collection 008workshop_dust_collection

Once the blast gates were in place on the trunk line, he extended PVC around the left side of the room, adding a wye connector at each tool. These connectors offer better air flow than a T connector because of the softer angle.


Every tool comes with a different type of hose to attach to a dust collection system. Aaron created custom adapters to reduce the line so that each tool’s hose could connect.

010workshop_dust_collection 011workshop_dust_collection

He continued the install by running PVC across the space and down the right side of the room. This required some funky angles thanks to all the things on the wall in this area.

013workshop_dust_collection 015workshop_dust_collection 016workshop_dust_collection

Here’s the full line installed, just waiting for tool attachments.


Here are some of the tool attachments in action.

018workshop_dust_collection 019workshop_dust_collection

Everything gets sucked back to the machine and collects in the bottom bag for easy removal.


So far the system works great on most of the tools, except the miter saw, which is an older tool. We’re blaming the tool, not the dust collection and Aaron is working on an adjustment for that.

As with most systems, this one was super necessary… but not super glamorous. What’s on your summer reno list? Anything more exciting?








The workshop is DONE!

This post has only been THREE YEARS in the making. But first can we talk about foot injuries and one-man construction crews? That combo really sucks… like drinking wine after brushing your teeth. It doesn’t make anyone happy. So it’s been unintentionally quiet here (and literally quiet at the firehouse) as Aaron’s foot heeled. He’s back in motion again and chomping at the bit to get projects back in flight for the living room/dining room redo.

Just before the foot injury claimed two months of his life, he finished the workshop and put it instantly to use to build a pantry for the new trailer… because he (ok… we…) can’t leave well enough alone. Now it’s clean and ready for its’ debut on the interwebs!

We already told you about dropping more power into the space, framing & painting, adding a window and lighting the place up, but there was more work to be done before this space was finished, including a bit of building and installing the dust collection system. (More on that last bit in the next post.)

First Aaron built a wall in the back of the workshop that he covered in pegboard to provide much needed hanging storage.



Then he built a table for the miter saw.

003workshop_after 004workshop_after 005workshop_after

Finally he created an out-feed table for the table saw.

006workshop_after 007workshop_after 008workshop_after

Ok – are you ready for the grand tour? When you come down the stairs, now you see this:


The slated plastic door helps keep dust contained in the workshop (and is really fun to walk through).

Once Aaron started laying out the workshop he realized how small it was relative to the amount of tools he wanted to put it in. So instead of going in the workshop, the lockers we’ve been hoarding are just to the left after you come down the stairs. They’re full of materials like painting supplies and extension cords. (If you’re not familiar with the layout we’re after, check out this post and it will make more sense.) Eventually this walkway will get more finishing touches.


Once you stop into the space it looks like this!!


The finished miter saw table has storage and a charging station below. Overhead a reel and hose make it easy to connect and use air-powered tools in the workshop without moving the air compressor.


On the opposite wall, the router table is tucked to the left (and on wheels for easy relocation) and the table saw and out-feed table dominate the room. This was strategically placed under a floor drain that dips low enough for Aaron to smash his head into.


The out-feed table also has storage below.


Moving left to right: a workbench, air conditioner, the dust collector, the finished pegboard wall, disc/belt sanderĀ and jointer.


Here’s the view from the back.


It’s been a long time coming, but it I think it was worth the wait. This space is amazing! Aaron has already used it for a few projects, and it’s a revelation not to have sawdust in our living space or be required to scoot around pieces of wood that have been painted and are drying. But, really, what I love the most about the workshop is that everything has a home… that isn’t my (future) dining room floor. There are all these little moments that make my organization loving heart so, so happy.

017workshop_after 018workshop_after 019workshop_after 020workshop_after 021workshop_after 022workshop_after

And because I’m sucker for a really good before and after. Here’s a look at 3+ years ago vs today.

023workshop_after 024workshop_after


Converting fixtures for LED and lighting up the workshop

Simply adding a window to the workshop was not enough to up the brightness factor. We knew we needed a serious lighting upgrade. We’ve been hoarding some moisture-proof industrial fluorescent fixtures that we picked up just for this space with the intention of converting them to LEDs.


And now we’re going to breakdown the process for taking a fluorescent fixture to an LED-enabled one. (If you’re just here for the pictures, don’t leave until you see the dramatic before and after shots at the bottom of the post.)


Tools/supplies needed:

  • Wiring diagram for LED bulbs (this should come with the bulbs)
  • Screwdriver
  • Wire snips
  • Vice grips
  • Replacement plug
  • Wire caps
  • Shunted keystones
  • Pencil
  • Utility knife
  • Wire strippers


First remove the outer case and the bulbs.


A clip in the middle of the interior panel holds it in place. Twist that to remove the panel.


Inside you’ll find the wiring and ballast for the fluorescent lights. You can reuse the wires, but you’ll want to remove the ballast.


Just snip the wires


Then undo the screws and it should slide out.


Remove the existing keystones (the white pieces at each end of the fixture that hold the bulbs in place and provide power).


Snip the wires from the keystones to free them.


Slide two of the new keystones into one side. LEDs only need wired on one side, so these un-wired keystones are just here to hold the bulbs in place.

013LEDinworkshop 014LEDinworkshop

For the other two keystones, consult the wiring diagram to determine which side of the keystone is the hot/load and which is neutral.


Strip 1/2″ from the end and slide the hot wire into the appropriate opening.


On the neutral side, use one keystone as the neutral in and out. It makes more sense in the pictures below.

018LEDinworkshop 019LEDinworkshop

Slide the wired keystones into place.


Next you need to connect the wires in the fixture to the wires leading to the power cord. Hot goes with hot. Neutral with neutral. Ground to the fixture case.

021LEDinworkshop 022LEDinworkshop

Now you can reinsert the interior panel to cover the wires.


When these fixtures were removed from their original home, the wire that provided power was snipped. We want to add a plug and power these through a receptacle, so this was not a big issue.



Loosen the screws to divide the plug into two pieces.


Run the wire through the base.


Strip the wire.


Connect it to the plug (follow your plug’s instructions)

  • Black (hot) to the gold screw
  • White (neutral) to the silver screw
  • Green (ground) to the stick part


Slide the two pieces together and tighten the screws.




When you add the bulbs, make sure you put the powered end (denoted here with an AC) with the wired keystone.




It seems like a lot of steps, but it goes pretty quickly once you get the hang of it. As always, we like to point out that we are not professionals. If you have any hesitation about doing electrical work it’s better to be safe than sorry. (Consult a pro.)

The change is dramatic! We took the workshop space from two single bulb incandescent fixtures that looked like this


to 8 double-LED fixtures. Now the space looks like this!!


There’s no photo trickery here. The space is THAT much brighter! The shadows are gone and this actually feels like a space where work can get done!

Obviously Aaron has also been busy assembling some of the tools we purchased for this space. We’ll give you a full run down whenever the space is done. Next up: dust collection & filtration.

Put a window in it

If we had a mantra (a la Portlandia’s “put a bird on it“) it would be a close tie between “paint it white” and “put a window in it”. In the case of the workshop, we’re doing both. You see the hole right there… we put a window in it.


The basement has two subterranean window openings that are protected by metal grates. They were boarded up, but not bricked over like the windows on the first floor, making this a really easy and inexpensive way to add some natural light to the space.


Remove the board…


Put a window in it…


Except when we removed the board, we discovered a small jungle of weeds and trash.


A little clean up and three bags of rock made this a much better view.


It’s not enough light to work by, but it makes a huge difference when you hit the bottom of the steps.


That’s it. Just an easy, simple “put a window in it” project.

Framing and painting the workshop

I feel like I can stop being a broken record. I don’t know how many times I’ve said, “We’re going to start the workshop,” or “The workshop is next!” or some iteration of that, but if we’re talking over/under 100… I’d bet over. Yesh! When it comes to this renovation, it’s always funny to look back at what we thought would happen vs. what actually did happen. Well, most days it’s funny…

But I digress. Here’s a statement I’m loving: The workshop is underway!

I thought you might need a refresher on the layout of the basement. It’s basically a blank slate with columns running down the middle.


Although it normally looks more like this…


We decided to dedicate nearly half of the space to the workshop (after changing things up a little.) The “New” layout is still the plan.


That required constructing walls between the columns and at the front of the workshop to define the space.


That picture kind of sucks. Here’s a better view with the walls filled in. We used 3/4″ treated plywood to serve as walls and work as a good base for anything Aaron wants to hang.


The walls and ceiling got a coat of white primer and white paint. Instantly it feels so much brighter and much more fresh in here.


He also topped the floor with two coats of Rustoleum’s EPOXYSHIELD in gray gloss (minus the flecks, because why do epoxy floors need specks?)

Here’s the opposite view (looking toward the stairs) before and after paint.

006workshopframepaint 007workshopframepaint

It feels GREAT to see progress on the workshop! Next up: moving some of the big tools in, running more electrical, and adding lights!

What’s your broken record project? The one you can’t stop talking about for good or bad reasons?